Repository navigation
Conversation
Values from the "Print Settings" on 3dfuel.com product pages. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_01BL4nqCNp6TbtdezfW2ysLk
|
Automated review of Corrects print and bed temperatures on four 3D-Fuel product lines and adds Pro PCTG drying and enclosure values. Not ready to merge: the Tough Pro PLA+ minimum nozzle temperature (220) contradicts the brand's current TDS (230-250 °C).
claude-haiku-5-5 · $0.02
Auto-merge: held back: E10 10 changed value(s) unproven; E12 0 check finding(s), 4 flip-flop(s). The Auto-merge check decides. Changed values: 0 of 10 proven
Maintainers: ✅ LGTM & merge · workflow run |
| "diameter_tolerance": 0.02, | ||
| "density": 1.22, | ||
| "min_print_temperature": 230, | ||
| "min_print_temperature": 220, |
There was a problem hiding this comment.
🔴 The brand's Tough Pro PLA+ TDS (Rev. October 2026, the newest sheet) gives the nozzle range as 230-250 °C, not 220-250 °C. The TDS is the authoritative source over the product page, so please keep the minimum at 230. (unverified: temperature must be a whole number of °C from 1 to 499)
| "diameter_tolerance": 0.02, | ||
| "density": 1.22, | ||
| "min_print_temperature": 230, | ||
| "min_print_temperature": 220, |
There was a problem hiding this comment.
Found by the bot; check the source before committing:
/min_print_temperature=230(high, source)
| "min_print_temperature": 220, | |
| "min_print_temperature": 230, |
| "min_print_temperature": 220, | ||
| "max_print_temperature": 250, | ||
| "min_bed_temperature": 0, | ||
| "max_bed_temperature": 60, |
There was a problem hiding this comment.
Found by the bot; check the source before committing:
/enclosure="not_needed"(high, source)/dry_temperature=50(high, source)/dry_time=8(medium, source) (Upper end of the 6-8 hour range, following the same mapping this PR uses for PCTG. The TDS gives no maximum drying temperature.)
| "max_bed_temperature": 60, | |
| "max_bed_temperature": 60, | |
| "dry_temperature": 50, | |
| "dry_time": 8, | |
| "enclosure": "not_needed", |
|
@Makemo07 could you please provide a source on why you're lowering these values? It would seem the TDS differs which would be a more reliable source IMO |
Source: the print settings stated on every product page on 3dfuel.com (product pages fetched October 2026; the same values on all colour pages of a line).
Drying range mapped as in #816–#819: lower temperature →
dry_temperature, upper →max_dry_temperature, upper hours →dry_time.Not changed: Pro ABS (discontinued, no print settings on the page), Silk PLA+ and Dual-Color Silk PLA+ (no product page found). Volumetric speed is not given by 3D-Fuel (only "Recommended Print Speed: 60 – 250 mm/s"); I have asked them.
The old PDF data sheets for Standard/Pro PLA (185–205 °C / 190–230 °C) predate the current PLA+ lines and were not used.
python -m ofd validate: all validations passed.🤖 Generated with Claude Code
https://claude.ai/code/session_01BL4nqCNp6TbtdezfW2ysLk