Skip to content
Merged
Show file tree
Hide file tree
Changes from all commits
Commits
File filter

Filter by extension

Filter by extension

Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
376 changes: 342 additions & 34 deletions bins/index.html

Large diffs are not rendered by default.

54 changes: 53 additions & 1 deletion docs/ENGINE.md
Original file line number Diff line number Diff line change
Expand Up @@ -745,6 +745,56 @@ currently installed):
the fan moves, every cut is taken again on it. Only then: a 6 mm magnet from above at
42 mm has a spoke 2.3 microns from a corner in every cell and is closed, and a cell open
somewhere else (a pocket meeting a joint's housing) gains nothing from a new floor.
Corners, not every point a wall stands on: where a counterbore and its shank were
unioned, the BSP split each flat of the shank along the head's planes, and with those
split points counted as well (24 on the socket floor, against the shank's 12 corners)
a 2.4 mm shank under a 4.8 mm head at 44.08 mm, loose, had a point within `FAN_CLEAR`
of every centre `fanCentre` tried. The fan stayed put and the cell shipped six edges
open. From the corners alone it moves 0.2 mm and the floor closes.
- **A pocket that reaches a joint's cut goes bad where the two ceilings are level.** A
key's recess, an H-clip's and a tab's notch are all cut up from under the plate, as a
magnet pocket from beneath and a counterbore are. Run into one, the pocket comes out
closed at nearly any depth but one: the recess's 2 mm (a 2 mm magnet, the default counterbore)
or the notch's 2.4 (the spec's 6.5 × 2.4 magnet), where the two ceilings share a face
that two subtractions each split their own way. A bowtie in the floor at 42 mm left 12
edges open at 7.9 mm and 19 at 10; puzzle tabs at 36 to 40 mm left 26 to 86 with the
spec's magnet. All 86 pockets tried level with a cut went bad; 0.001 mm off it, 3 did,
and 0.003 mm or more off it, none. Off the level it depends on the cut, and `mountLimits`
measures every mounting site of a whole cell against each cut on the layout, by the
pocket's own polygon (`boreReach`), not the circle through its corners:
- **A key's recess, an H-clip's or a puzzle tab's notch takes no pocket.** A sliver in
can go bad off the level too: 0.019 mm into a snap key's recess at 36.52 mm, with a
0.5 mm fit clearance, on main at four depths. Let in wherever the magnet or screw stays
clear of the key or tab, 7 of 2,519 such pockets at the default fit or tighter went bad
(0.02 to 0.14 mm in), and 8 of 1,151 at looser fits (0.2 to 0.65 mm in).
- **A dovetail's notch takes a pocket from beneath**, a sliver or deep, unless it is
level with the notch (within 0.05 mm either way, `MOUNT_LEVEL`, measured to the
micron) or the magnet or screw in it would reach the other piece's tab,
which stands the fit clearance inside the notch. None of 3,699 such designs went bad,
1,086 of them on the page's design at 40.5 to 44.5 mm. A 12.7 mm magnet at 42 mm, 2 or
3 mm thick, is taken: its pocket is 0.04 to 0.09 mm into the notch and the magnet
0.24 mm clear of the tab. 2.4 mm thick it is level, built 96 bad edges, and is refused.
- **A pocket from above** meets any of them unless its floor stands a layer over the
cut's ceiling. The housings a key is dropped into from above start 1.3 mm over the
socket floor and nothing reaches them, and a pocket in a corner boss is left out: the
boss is a shell of its own, and no joint is cut from it.

A pocket that stops short of a cut stops 0.01 mm short (`MOUNT_SEAM`): the weld in
`healCsgSeams` takes points `VTOL` apart for one, and a thinner wall can come out welded
through. 4 of 715 pockets less than 0.005 mm short went bad, and none of 1,941 from 0.005
to 0.03 mm. Under a dovetail's notch that leaves a few hundredths of a millimetre of
refused sizes below the largest, between the pocket that stops 0.01 mm short and the one
that breaks in, about 0.02 mm wide and rounded out to the hundredth either side, as the
field takes them: at 36 mm on the page's design 5.59, 5.6, 5.73 and 5.74 mm are refused,
and 5.58, 5.61, 5.72 and 5.75 are taken. The page says so at the field and names the
sizes taken either side. Past the weld's reach there is still the
lottery the room cannot see, about one design in a thousand, single sizes with clean
ones on either side, and it needs the pocket and the cut together: a 14.1 mm
counterbore 2.4 to 3 mm deep, 0.09 mm short of a dovetail's notch at 43.17 mm, loose,
folds an edge at the notch's corner, byte for byte as main does, and is clean at 2.35 mm
deep, at 14.075 and 14.125 mm across, at every size from there into the notch, and with
no counterbore. A guard out that far would refuse sizes that build clean on both sides
of it and still miss the next, 0.1 mm off.
- **A joint's cut is the same lottery, and below 16 mm it comes up often.** The socket's
straight walls run only 2.5 mm either side of a cell's middle at 13.5 mm, so every
housing, notch and clip pocket crosses its corner arcs and cones, at points that move
Expand Down Expand Up @@ -782,7 +832,9 @@ currently installed):
nothing cleared (10.1 to 11.1 mm magnets at 47.91 to 50.05 mm, clean on main). And once
the cells are built, if the shells `settle` cut again have more bad edges with those
beside them than they started with, or more open or turned over, they all go back to
their first cut. Two cups put in
their first cut. That check sees only those shells and their neighbours as the cells
left them: the dovetail and puzzle tabs are made after it, and the top-insert pass cuts
its housings out of shells after it, so neither is judged by it. Two cups put in
from above from each side of a piece one cell deep meet face to face at 14.44 mm (twice a
cup's reach), and there they are built as one solid with `csgUnion`.
- **A face that is nothing but a straight line has no middle.** A weld that closes a
Expand Down
Loading
Loading