Skip to content
Merged
Show file tree
Hide file tree
Changes from all commits
Commits
File filter

Filter by extension

Filter by extension

Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
12 changes: 8 additions & 4 deletions README.md
Original file line number Diff line number Diff line change
Expand Up @@ -132,7 +132,7 @@ For the historical 3.0.2 notice bundles, see [their separate checksums](licenses
## Supported hardware

<p align="center">
<img src="assets/diagrams/hardware.svg" alt="ESP32-S3 N16R8 or N8R8 board, independent USB power, optional microSD and optional W5500 Ethernet." width="100%">
<img src="assets/diagrams/hardware.svg" alt="ESP32-S3 N16R8 or N8R8 board. Tested 4G setup: one charger on an OTG Y-cable powers the board and a TCL LinkKey IK41 SIM stick; computer on the COM port optional; optional microSD, W5500 Ethernet and UART modem." width="100%">
</p>

Firmware 3.x runs on **ESP32-S3 with 8 MB octal PSRAM and at least 8 MB of
Expand Down Expand Up @@ -182,13 +182,17 @@ you. As an Amazon Associate I earn from qualifying purchases.*

- **The board does not supply 5 V on its USB port.** Use a powered USB-C OTG
Y-cable with a 5 V charger (at least 2.5 A for a modem or stick), or the
device's own 5 V supply with grounds connected. LTE modems draw **up to 2 A**
device's own 5 V supply with grounds connected. **Tested:** a single charger
on the Y-cable's power input runs both the board and a TCL LinkKey IK41
stick (cable plug in the board's USB port, stick in the cable's socket),
with nothing on the COM port. LTE modems draw **up to 2 A**
in bursts: a computer's USB port is not enough (modem resets, reset reason
BROWNOUT).
- Never connect two 5 V sources together: if you bridge the board's USB-OTG
pad, never plug that port into a computer or charger.
- After the restart the USB port is a USB host: flash, logs and power go
through the COM port. One device, no hubs, about 10 Mbit/s at most.
- After the restart the USB port is a USB host: flash and logs go through the
COM port; power can come from the Y-cable alone. One device, no hubs, about
10 Mbit/s at most.
- **While a USB connection is on, the Wi-Fi keeps 16 receive buffers instead of
24** to leave internal RAM for the device. Bursts of Wi-Fi traffic, such as
a speed test from a phone on the gateway's access point, can be slower or
Expand Down
39 changes: 1 addition & 38 deletions assets/diagrams/hardware.svg
Loading
Sorry, something went wrong. Reload?
Sorry, we cannot display this file.
Sorry, this file is invalid so it cannot be displayed.
3 changes: 3 additions & 0 deletions docs/USB-DEVICES.md
Original file line number Diff line number Diff line change
Expand Up @@ -86,6 +86,9 @@ socket for the device, and one power input for a USB charger.
```

- The charger powers the device and, through the cable, usually the board too.
**Tested** on an ESP32-S3-DevKitC-1 N16R8 with a TCL LinkKey IK41 stick: one
charger on the power input runs both the board and the stick, with nothing
connected to the COM port.
- Check the cable's description: it must pass **data** to the USB-C plug and
**power** to the USB-A socket. Charge-only splitters do not work.
- Keep the COM port free or connected to a computer only for logs; both can be
Expand Down
Loading
Loading